Catalog Searcher
Categories

Covertech Steel Substrate Type Steel Type

カバーテック 鋼材下地用 / Japan Power Fastening Corporation (Official website)

Drill screw for roof cover method on steel substrate. Low-cost type combining a steel washer.

Last verified: (date the content was verified against the source document)

Specifications

Nominal diameter d 6 mm
Pitch P 1.8 mm
Washer Outer Diameter 25 mm
Nominal length range 60～135 mm
Applicable plate thickness (lower limit) 1.6 mm
Applicable plate thickness (upper limit) 4.5 mm

カバーテック 鋼材下地用 model comparison

Compare 3 models in the same series by specification.

Model Nominal diameter d Pitch P Applicable plate thickness (lower limit) Applicable plate thickness (upper limit) Nominal length range Washer Outer Diameter
カバーテック鋼材下地用 スコッツタイプ 6 mm 1.8 mm 1.6 mm 4.5 mm 60～135 mm 25 mm
カバーテック鋼材下地用 スコッツタイプ本体 6 mm 1.8 mm 1.6 mm 4.5 mm 90～150 mm —
カバーテック鋼材下地用 スチールタイプ This product 6 mm 1.8 mm 1.6 mm 4.5 mm 60～135 mm 25 mm

How to choose Screws and bolts

Points to check when selecting, with the values for this product (Covertech Steel Substrate Type Steel Type).

  1. 1. Select a type that suits the substrate

    Drill screws are used for steel substrates, S-cut tip or double-thread screws for wood substrates, and dedicated lift-prevention tip products for existing slate or shingle roofs. Each substrate type has a different structure. Confirm the existing roof construction and substrate material before selecting.

  2. 2. Check the drillable sheet thickness for steel substrates

    This product: Applicable plate thickness (upper limit) 4.5 mm

    Drill screws have an upper limit on drillable steel sheet thickness. Listed products have an upper limit of 3.2 to 4.5 mm and a lower limit of 1.6 mm. Confirm that the thickness of the substrate steel, such as purlins, falls within this range, and also check tip specifications such as pilot length of 12 mm and cutting blade outer diameter of 3.4 mm.

  3. 3. Length suited to the total thickness of stacked materials

    Re-roofing construction passes through the new roofing, existing roofing, insulation and other layers, so confirm the maximum clamping thickness. The maximum clamping thickness of the listed product is 30 mm. Some are available in series lengths such as 90 to 150 mm. Select a length that allows sufficient engagement into the substrate beyond the total thickness.

  4. 4. Check nominal diameter and pitch

    This product: Nominal diameter d 6 mm

    Listed products have a nominal diameter of 4.5 to 6.3 mm and a pitch of 1.8 to 2 mm. A larger diameter gives greater holding power but also affects the hole diameter in the substrate and roofing. Also confirm the manufacturer's specified size and compatibility with the bits and drivers used for installation.

  5. 5. Compare pull-out and shear strengths

    Roofs receive uplift forces from wind suction. Listed products show values of 5.9 kN in steel substrates, 2.5 kN in wood substrates, up to 600 N in structural plywood substrates, and maximum shear of 1200 N. Use the values for each substrate in calculating the required design strength and the number of fasteners.

  6. 6. Washer material and outer diameter for waterproofing

    This product: Washer Outer Diameter 25 mm

    Washers are available in stainless steel with gasket, low-cost steel types, and others, with outer diameters of 25 mm and 20 mm. Select based on roofing profile, the area to be pressed, the risk of rainwater infiltration, and dissimilar metal contact with the roofing material. Some products are supplied as the body only without a washer.

This guide was written by AI based on the listed products' documents and specification items.

About Screws and bolts and all products

Description

The washer is made of steel and used in combination with Neo Packing. Washer outer diameters are available in two types, 25 mm and 20 mm, and lengths range from 6×60 mm to 6×135 mm.

Features

  • Low-cost type with steel washer
  • Two washer outer diameters: 25 mm and 20 mm
  • Drill screw type

Applications

  • Roof cover method for metal roofs (steel substrate)

FAQ

Q. What is the model number of the Covertech Steel Substrate Type Steel Type?
A. No model number is listed in the product information. The product name is Covertech Steel Substrate Type Steel Type, and the series is Covertech Steel Substrate Type.
Q. What kind of roofing work can the Covertech Steel Substrate Type Steel Type be used for?
A. It is a drill screw used for the roof cover method on metal roofs (steel substrate).
Q. What are the washer material, outer diameter, and combination used with the Covertech Steel Substrate Type Steel Type?
A. The washer is made of steel and used in combination with Neo Packing. Washer outer diameters are available in two types, 25 mm and 20 mm.
Q. What are the nominal diameter, pitch, nominal length, and applicable plate thickness of the Covertech Steel Substrate Type Steel Type?
A. Nominal diameter d is 6 mm and pitch P is 1.8 mm. Nominal length is 60 to 135 mm, and applicable plate thickness is 1.6 mm to 4.5 mm.

Written by AI based on the content of the source documents.

Source documents

More products from Japan Power Fastening Corporation

See all →