Low-Noise Deep Groove Ball Bearing for Motors, 60 Series

Specifications

How to choose Deep Groove Ball Bearings

Points to check when selecting, with the values for this product (Low-Noise Deep Groove Ball Bearing for Motors, 60 Series).

1. 1. Main dimensions to suit shaft and housing

   This product: Inner diameter d 10～15 mm

   Select the bore diameter d to match the shaft diameter, the outside diameter D to match the housing bore, and the width B to suit the installation space. The listed products cover a wide range of bore diameters from 0.6 to 1420 mm, and even at the same bore diameter there are dimension series with different outside diameters and widths. Since load capacity and mass change with the dimension series, confirm the three dimensions in combination.

2. 2. Basic dynamic load rating for life calculation

   The basic dynamic load rating Cr is the reference value for calculating rolling fatigue life, and life is estimated from the ratio of the actual applied load to Cr. For high loads or when long life is required, select a bearing with a larger Cr. Bearings made of special materials may have lower ratings than steel bearings of the same dimensions, so confirm life under the operating conditions.

3. 3. Check static and shock loads against static rating

   The basic static load rating C0r is the guideline load at which permanent deformation does not occur, applicable when stationary, rotating at low speed, or subjected to shock loads. For applications with oscillating motion or large loads while stopped, select with emphasis on the ratio to C0r (static safety factor) rather than the dynamic rating.

4. 4. Internal clearance to suit fit and temperature

   Radial internal clearance decreases during operation due to interference fits and temperature differences between the inner and outer rings. Clearances larger than standard, such as C3, are used in applications where the inner ring tends to expand, such as motors or high-temperature environments. Clearance that is too small leads to heat generation and seizure, so determine the class from the fit and operating temperature.

5. 5. Materials and lubrication suited to the environment

   Stainless steel or ceramics (silicon nitride, zirconia, silicon carbide) are used in water or chemical solutions, while solid lubricants such as graphite or fluorine-based solids and fluorine grease are used in high-temperature, vacuum or clean environments. Listed products have maximum operating temperatures of 250 to 350°C, so select the material and lubrication method based on temperature, atmosphere and dust-generation requirements.

6. 6. Check speed limits and electrical corrosion countermeasures

   Confirm that the limiting speed and reference speed exceed the operating speed. In equipment where shaft current flows, such as inverter-driven motors, hybrid bearings with insulating-coated or ceramic balls can prevent electrolytic corrosion. Ceramic balls are lighter than steel balls, so the effect of centrifugal force is reduced even at high speeds.

This guide was written by AI based on the listed products' documents and specification items.

About Deep Groove Ball Bearings and all products

Description

Three-dimensional analysis optimizes the raceway surface properties in the rolling direction, reducing sound pressure in the 1,000Hz to 5,000Hz range, which people perceive as unpleasant, compared with conventional products. Compact bearings with bore diameters of 10 to 15 mm. Shielded and sealed versions are available.

FAQ

Q. What type of noise reduction is the Low-Noise Deep Groove Ball Bearing 60 Series designed for?

A. The raceway surface properties are optimized through three-dimensional analysis to reduce sound pressure in the 1,000Hz to 5,000Hz range, which people perceive as unpleasant, compared with conventional products.

Q. What are the bore, outside diameter, and width ranges of the Low-Noise Deep Groove Ball Bearing 60 Series?

A. They are available in 3 sizes: bore diameter d 10 to 15 mm, outside diameter 26 to 32 mm, and width 8 to 9 mm.

Q. Can the Low-Noise Deep Groove Ball Bearing 60 Series be used with shields or seals?

A. Yes, shielded and sealed versions are available.

Q. What applications are the Low-Noise Deep Groove Ball Bearing 60 Series suited for?

A. They are suited for household motors, industrial motors, and machinery used indoors or near people.

Q. What are the basic load ratings and permissible rotational speeds of the Low-Noise Deep Groove Ball Bearing 60 Series?

A. Basic dynamic load rating Cr is 5.70 to 7.00 kN and basic static load rating Cor is 1.95 to 2.85 kN. Permissible rotational speed is 23,000 to 31,000 min-1 with grease lubrication and 27,000 to 36,000 min-1 with oil lubrication.

Written by AI based on the content of the source documents.

Source documents

• Catalog モータ用 良音質深溝玉軸受 Open page 1
  Found on: https://koyo.jtekt.co.jp/products/type/deep-groove-ball-bearing/