Catalog Searcher
Categories

Tapered Roller Bearing KEST4190LFTUR4

Model KEST4190LFTUR4 / KE軸受 / JTEKT Corporation (Official website) / Listed on page 5 of the document

Tapered roller bearing for axle drive pinion. Adopts KE bearing technology and low torque specification (LFT).

Last verified: (date the content was verified against the source document)

Tapered Roller Bearing KEST4190LFTUR4 on page 5 of JTEKT Corporation "円すいころ軸受 アクスルドライブピニオン用"
Source: JTEKT Corporation「円すいころ軸受 アクスルドライブピニオン用」page 5
A reduced image of the relevant page is quoted from the document. Copyright belongs to JTEKT Corporation.Request removal

Specifications

Inner diameter d 41.275 mm
Outer diameter D 90.000 mm
Width T 30.006 mm
Inner ring width B 30.006 mm
Outer ring width C 21 mm
Basic dynamic load rating Cr 112 kN
Basic static load rating C0r 112 kN
Fatigue Limit Load Cu 16.2 kN
Point of Action Position a 29.0 mm
Coefficient e 0.70
Axial load factor Y1 0.86
Axial load factor Y0 0.47
Mass 0.866 kg

KE軸受 model comparison

Compare 11 models in the same series by specification.

Model Inner diameter d Outer diameter D Width T Basic dynamic load rating Cr Basic static load rating C0r Inner ring width B Outer ring width C Coefficient e
KEST3072CLFT 30 mm 72 mm 20.750 mm 71.2 kN 55.6 kN 19 mm 14 mm 0.55
KEST4183YR1LFT 41.275 mm 82.550 mm 26.543 mm 85.8 kN 75.3 kN 25.654 mm 18 mm 0.72
KEST4190LFTUR4 This product 41.275 mm 90.000 mm 30.006 mm 112 kN 112 kN 30.006 mm 21 mm 0.70
KESTA3779LFT 36.513 mm 79.375 mm 29.370 mm 100 kN 96.4 kN 27.2 mm 20.4 mm 0.67
KESTA4895-1LFTUR4 47.625 mm 95.250 mm 30.162 mm 127 kN 133 kN 29.37 mm 20.5 mm 0.70
KESTD3368LFT 33.338 mm 68.263 mm 22.225 mm 66.1 kN 62.2 kN 22.225 mm 15.25 mm 0.70
KESTJ4090LFT 40 mm 90 mm 26.500 mm 110 kN 106 kN 26 mm 18.5 mm 0.62
KESTN3580LFT 35 mm 80 mm 29.000 mm 100 kN 96.4 kN 27.2 mm 20 mm 0.50
KESTR3572LFTYR1 34.925 mm 72.233 mm 23.579 mm 78.8 kN 75.0 kN 23.106 mm 15.463 mm 0.70
KETRD091004UR4 45 mm 100 mm 38.000 mm 164 kN 183 kN 36.5 mm 27.5 mm 0.76
KETRD101004UR4 50.800 mm 104.775 mm 36.512 mm 171 kN 177 kN 34 mm 25.5 mm 0.67

How to choose Tapered Roller Bearings

Points to check when selecting, with the values for this product (KEST4190LFTUR4).

  1. 1. Dimension series matching shaft and housing

    This product: Inner diameter d 41.275 mm

    Bore d matches the shaft diameter and outside diameter D matches the housing bore. Tapered roller bearings come in metric and inch series, and bearings of similar size are not interchangeable. When replacing bearings in existing machinery, confirm the series of the boundary dimension designation, and check inner ring width B and outer ring width C against the step dimensions of the mounting section.

  2. 2. Managing preload with assembled width T and tolerance

    This product: Width T 30.006 mm

    Width T is the overall width of the inner and outer rings when assembled, and it affects axial mounting dimensions and the adjustment amount for preload or clearance. The assembled width tolerance class changes the effort required for adjustment, so when used in pairs, confirm T and its tolerance class.

  3. 3. Estimating life with basic dynamic load rating

    This product: Basic dynamic load rating Cr 112 kN

    Basic dynamic load rating Cr is the basis for life calculation. From radial and axial loads, the dynamic equivalent load is obtained using factor e and load factor Y1, and rated life is calculated from the ratio to Cr. The listed Cr values range from 9.5 kN to several tens of thousands of kN and vary greatly with the number of rows.

  4. 4. Checking shock and low-speed use with static load rating

    This product: Basic static load rating C0r 112 kN

    For applications with stationary operation, very low speed, or shock loads, check the margin against permanent deformation using the ratio of basic static load rating C0r to the static equivalent load (calculated with Y0). For heavy-duty rolling mills and similar uses, secure capacity with double-row or four-row types.

  5. 5. Determining shaft support by load action point position

    This product: Point of Action Position a 29.0 mm

    Tapered roller bearings have load action points located away from the end face, and the span between supports changes depending on back-to-back or face-to-face arrangement. Use the load action point position a for calculating shaft deflection and reaction forces, and determine the mounting direction accordingly.

  6. 6. Matching rotational speed and lubrication method

    The permissible rotational speed is set higher for oil lubrication than for grease lubrication. Confirm that the operating speed is within the value for each lubrication method. For differentials and other applications where energy saving is required, low-torque types showing the friction torque reduction rate are also candidates.

This guide was written by AI based on the listed products' documents and specification items.

About Tapered Roller Bearings and all products

Features

  • Extended bearing life through KE bearing technology
  • Low torque specification (LFT)

Applications

  • Automotive axle (drive pinion)

FAQ

Q. What are the applications and main features of KEST4190LFTUR4?
A. It is a tapered roller bearing for automotive axles (drive pinion). Key features are extended bearing life through KE bearing technology and the low torque specification (LFT).
Q. What are the dimensions and mass of KEST4190LFTUR4?
A. Bore diameter d is 41.275 mm, outside diameter D is 90.000 mm, width T is 30.006 mm, inner ring width B is 30.006 mm, and outer ring width C is 21 mm. Mass is 0.866 kg.
Q. What are the basic dynamic and static load ratings and the fatigue limit load of KEST4190LFTUR4?
A. Basic dynamic load rating Cr is 112 kN, basic static load rating C0r is 112 kN, and fatigue limit load Cu is 16.2 kN.
Q. What are the coefficients and load center location used in calculations for KEST4190LFTUR4?
A. Load center location a is 29.0 mm and factor e is 0.70. Axial load factors are Y1 0.86 and Y0 0.47.

Written by AI based on the content of the source documents.

Source documents

Similar products from other manufacturers (alternatives)

Products from other manufacturers that match KEST4190LFTUR4 on two or more numeric specifications such as dimensions or ratings. Type and compatibility are not guaranteed; check each manufacturer's documents before adopting.

Similar products (other manufacturers)

Tapered Roller Bearings products, ordered by similarity of specifications and applications.

More products from JTEKT Corporation

See all →