Sealed Hybrid Deep Groove Ball Bearing (d 50-75 mm)

Specifications

How to choose Deep Groove Ball Bearings

Points to check when selecting, with the values for this product (Sealed Hybrid Deep Groove Ball Bearing (d 50-75 mm)).

1. 1. Main dimensions to suit shaft and housing

   This product: Inner diameter d 50～75 mm

   Select the bore diameter d to match the shaft diameter, the outside diameter D to match the housing bore, and the width B to suit the installation space. The listed products cover a wide range of bore diameters from 0.6 to 1420 mm, and even at the same bore diameter there are dimension series with different outside diameters and widths. Since load capacity and mass change with the dimension series, confirm the three dimensions in combination.

2. 2. Basic dynamic load rating for life calculation

   This product: Basic dynamic load rating Cr 37.1～68.9 kN

   The basic dynamic load rating Cr is the reference value for calculating rolling fatigue life, and life is estimated from the ratio of the actual applied load to Cr. For high loads or when long life is required, select a bearing with a larger Cr. Bearings made of special materials may have lower ratings than steel bearings of the same dimensions, so confirm life under the operating conditions.

3. 3. Check static and shock loads against static rating

   The basic static load rating C0r is the guideline load at which permanent deformation does not occur, applicable when stationary, rotating at low speed, or subjected to shock loads. For applications with oscillating motion or large loads while stopped, select with emphasis on the ratio to C0r (static safety factor) rather than the dynamic rating.

4. 4. Internal clearance to suit fit and temperature

   Radial internal clearance decreases during operation due to interference fits and temperature differences between the inner and outer rings. Clearances larger than standard, such as C3, are used in applications where the inner ring tends to expand, such as motors or high-temperature environments. Clearance that is too small leads to heat generation and seizure, so determine the class from the fit and operating temperature.

5. 5. Materials and lubrication suited to the environment

   Stainless steel or ceramics (silicon nitride, zirconia, silicon carbide) are used in water or chemical solutions, while solid lubricants such as graphite or fluorine-based solids and fluorine grease are used in high-temperature, vacuum or clean environments. Listed products have maximum operating temperatures of 250 to 350°C, so select the material and lubrication method based on temperature, atmosphere and dust-generation requirements.

6. 6. Check speed limits and electrical corrosion countermeasures

   Confirm that the limiting speed and reference speed exceed the operating speed. In equipment where shaft current flows, such as inverter-driven motors, hybrid bearings with insulating-coated or ceramic balls can prevent electrolytic corrosion. Ceramic balls are lighter than steel balls, so the effect of centrifugal force is reduced even at high speeds.

This guide was written by AI based on the listed products' documents and specification items.

About Deep Groove Ball Bearings and all products

Description

Bearing combining silicon nitride rolling elements with double-sided FKM seals (2RS1), filled with standard grease WT. The reference speed is the value of the basic design bearing.

FAQ

Q. What applications are the SKF hybrid deep groove ball bearings 6210-2RS1 to 6215-2RS1 series suited for?

A. They are pre-lubricated at shipment and suitable for electric motors, generators, industrial high-speed drives, and similar applications.

Q. What are the bore and outside diameter ranges of the SKF hybrid deep groove ball bearings 6210-2RS1 to 6215-2RS1 series?

A. Bore diameter d is 50-75 mm and outside diameter D is 90-130 mm.

Q. What are the rolling element and seal configurations of the SKF hybrid deep groove ball bearings 6210-2RS1 to 6215-2RS1 series?

A. The rolling elements are made of silicon nitride, and the bearings have FKM seals (2RS1) on both sides. They are filled with standard grease WT.

Q. What is the basic dynamic load rating (Cr) of the SKF hybrid deep groove ball bearings 6210-2RS1 to 6215-2RS1 series?

A. The basic dynamic load rating Cr is 37.1-68.9 kN.

Q. Does the SKF sealed hybrid deep groove ball bearing (d 50-75 mm) require relubrication maintenance?

A. No. It is pre-greased at shipment and maintenance-free.

Written by AI based on the content of the source documents.

Source documents

• Catalog SKF 転がり軸受カタログ 15 エンジニアリング製品 15A センサー軸受ユニット 120 pages Open page 87
  Found on: https://azuma-eg.com/catalogue/