Catalog Searcher
Categories

Fine Tex Fine Thread Single Type 4.2×16

Model 167145 / ファインテクス 細目シーリングタイプ / Japan Power Fastening Corporation (Official website)

Stainless steel drill screw for thin sheets. Single type without washer, applicable to fastening thickness of 0.8 to 8.0 mm.

Last verified: (date the content was verified against the source document)

Specifications

Nominal diameter 4.2 mm
Length (under head) L 16 mm
Thread length 12.5 mm
Head outer diameter 9.0 mm
Head height 2.5 mm
Cross recess #2
Cutting edge diameter 2.9 mm
Cutting edge length 3.5 mm
Applicable plate thickness 0.4~1.2 mm
Grip length 0.8~8.0 mm
Box quantity 1000 本
Outer carton quantity 10 箱
Number of outer cartons (pieces) 10000 本
JAN 4533430+096641

ファインテクス 細目シーリングタイプ model comparison

Compare 7 models in the same series by specification.

Model Nominal diameter Length (under head) L Applicable plate thickness Grip length Cross recess Thread length Head outer diameter Head height
167134 4.2 mm 13 mm 0.4~1.2 mm 0.8~5.0 mm #2 9.5 mm 9.0 mm 2.5 mm
167145 This product 4.2 mm 16 mm 0.4~1.2 mm 0.8~8.0 mm #2 12.5 mm 9.0 mm 2.5 mm
167156 4.2 mm 19 mm 0.4~1.2 mm 0.8~11.0 mm #2 15.5 mm 9.0 mm 2.5 mm
167167 4.2 mm 16 mm 0.4~1.2 mm 0.8~6.0 mm #2 12.5 mm 9.0 mm 2.5 mm
167178 4.2 mm 19 mm 0.4~1.2 mm 0.8~9.0 mm #2 15.5 mm 9.0 mm 2.5 mm
167794 4.2 mm 16 mm 0.4~1.2 mm 0.8~6.0 mm #2 12.5 mm 9.0 mm 2.5 mm
167805 4.2 mm 19 mm 0.4~1.2 mm 0.8~9.0 mm #2 15.5 mm 9.0 mm 2.5 mm

How to choose Drill screws

Points to check when selecting, with the values for this product (167145).

  1. 1. Select the under-head length to suit the total fastening thickness

    This product: Grip length 0.8~8.0 mm

    If the under-head length of a drill screw is insufficient for the total thickness of the parts, the thread will not sufficiently engage after the cutting edge passes through, and adequate holding force will not be achieved. In the listed examples, the 4.2×13 fastens a thickness of 0.8 to 5.0 mm, while the 4.2×19 accepts up to 11.0 mm, so the upper limit changes with length. For washer types, confirm that the maximum fastening thickness is smaller even at the same length.

  2. 2. Check the drillable plate thickness

    This product: Applicable plate thickness 0.4~1.2 mm

    There is a limit to the steel sheet thickness through which the drill tip can cut a hole. In plates thicker than the cutting edge length, the thread engages before the cutting edge breaks through, causing seizure or breakage. Confirm that the thickness of the base steel sheet is within the applicable plate thickness range. In the listed example, the cutting edge diameter is 2.9 mm and the cutting edge length is 3.5 mm.

  3. 3. Check consistency of length and dimensions

    This product: Length (under head) L 16 mm

    The under-head length L is the length from the bearing surface of the head to the tip, which differs from the screw length. In the listed examples, L ranges from 13 to 19 mm and the screw length from 9.5 to 15.5 mm. The cutting tip portion has no thread, so judge actual thread engagement by the screw length, and also check the amount of protrusion on the back side.

  4. 4. Select diameter to determine holding force and plate thickness

    This product: Nominal diameter 4.2 mm

    The nominal diameter affects pull-out strength and shear strength, and should be selected according to the target member and base thickness. The listed example has a nominal diameter of 4.2 mm, and its fine thread is designed to secure enough thread engagement even in thin sheets. The stripping torque (the torque at which the thread is stripped) stated in the product features is also a useful guide for tightening control.

  5. 5. Choose a washer type where waterproofing is required

    On roofs, exterior walls and other areas exposed to rain, a sealing washer type helps reduce water ingress through the screw hole. There are an integrated EPDM washer type and a two-piece washer type, and the listed examples have washer outer diameters of 11 to 12.7 mm. The head protrudes by the washer height (3.4 to 3.5 mm), so also check the installation clearance.

  6. 6. Use a bit that matches the Phillips recess number

    This product: Cross recess #2

    If the Phillips recess number does not match the driver bit size, cam-out (the bit lifting out of the recess) can deform the head or prevent thrust from being transmitted during drilling. Confirm in advance that the power tool and bit number used for installation match the Phillips recess of the product.

This guide was written by AI based on the listed products' documents and specification items.

About Drill screws and all products

Description

Latest thin sheet dedicated drill screw made of SUS. Adopts Sus Guard SG, improving stripping torque and back torque to suppress slipping and loosening. Made in Japan.

Features

  • Increased stripping torque
  • Increased back torque
  • Single type (no washer)

Applications

  • Fixing thin sheet roofs and exterior walls
  • Installation of metal folded plate roofing

FAQ

Q. What is the fastening thickness range of Fine Tex Fine Thread Single Type 4.2×16 (model number 167145)?
A. The fastening thickness is 0.8 to 8.0 mm. The applicable sheet thickness is 0.4 to 1.2 mm.
Q. What are the main applications of Fine Tex Fine Thread Single Type 4.2×16 (model number 167145)?
A. It is used for fixing thin sheet roofs and exterior walls, and for installation of metal folded plate roofing.
Q. What are the material and features of Fine Tex Fine Thread Single Type 4.2×16 (model number 167145)?
A. It is a stainless steel drill screw made of SUS. It adopts Sus Guard SG, improving stripping torque and back torque to suppress slipping and loosening. It is a single type without washer.
Q. What are the dimensions and Phillips recess specifications of Fine Tex Fine Thread Single Type 4.2×16 (model number 167145)?
A. Nominal diameter is 4.2 mm, length under head L is 16 mm, and thread length is 12.5 mm. Head outer diameter is 9.0 mm, head height is 2.5 mm, and the Phillips recess is #2. Cutting edge diameter is 2.9 mm and cutting edge length is 3.5 mm.
Q. What are the packaging quantities of Fine Tex Fine Thread Single Type 4.2×16 (model number 167145)?
A. BOX quantity is 1000 pieces, outer case quantity is 10 boxes, and outer case piece count is 10000 pieces.

Written by AI based on the content of the source documents.

Source documents

Similar products (other manufacturers)

Drill screws products, ordered by similarity of specifications and applications.

More products from Japan Power Fastening Corporation

See all →