High-Precision Reducer for Servo Motors AH2 Type

Specifications

GTR model comparison

Compare 5 models in the same series by specification.

How to choose Speed reducers

Points to check when selecting, with the values for this product (High-Precision Reducer for Servo Motors AH2 Type).

1. 1. Determine the reduction ratio from the required speed and torque

   This product: Reduction Ratio 1/5～1/240

   The output rotational speed equals the motor rotational speed divided by the reduction ratio, and the output torque is approximately the reduction ratio times the input torque (minus transmission efficiency losses). Determine the rotational speed and torque required on the load side first, then select a reduction ratio that satisfies both.

2. 2. Provide margin in the permissible output torque

   Confirm that the rated output torque of the output shaft exceeds the load torque. Because torque beyond the rating is applied during startup and stopping, also check the permissible peak torque at startup and stop (as a percentage of rated torque; for example, some products are rated at 350%).

3. 3. Check the motor capacity to be combined

   This product: Applicable motor capacity 100W～2000W

   Each reducer has a specified motor output that can be mounted. If the motor capacity is too large, the torque after reduction may exceed the permissible value, so select within the applicable motor capacity range and also confirm compatibility of the mounting flange.

4. 4. Backlash according to positioning accuracy

   This product: Backlash 30 min (excluding some models)

   Backlash is the play in the rotational direction of the output shaft, measured in arcminutes (1/60 degree). For positioning and reciprocating motion, smaller is better; some products are available in 1 arcminute or 3 arcminutes, and some traction drive products offer no-backlash operation.

5. 5. Select the shaft category that suits the equipment layout

   The choice of coaxial, parallel or right-angle shaft changes the arrangement inside the equipment. Right-angle shafts allow a reduced depth through right-angle mounting, and hollow shafts allow a mating shaft to be inserted directly. Also check whether leg mounting or flange mounting is required.

6. 6. Check input speed and external dimension constraints

   For high-speed operation, confirm that the instantaneous maximum input rotational speed (for example, 7000 r/min) is not exceeded. Also verify at the design stage that the outer diameter fits the installation space and whether the unit can replace an existing product with identical dimensions.

This guide was written by AI based on the listed products' documents and specification items.

About Speed reducers and all products

Description

Foot-mounted type supporting right-angle shaft layout. Shares the gear head section with the induction geared motor, facilitating replacement of existing equipment.

FAQ

Q. Which motor capacities are supported by the High-Precision Reducer for Servo Motors AH2 Type (GTR Series)?

A. Applicable motor capacities are 100W to 2000W.

Q. What is the reduction ratio range and backlash value of the High-Precision Reducer for Servo Motors AH2 Type (GTR Series)?

A. The reduction ratio is 1/5 to 1/240. Backlash is 30 arcminutes, except for some models.

Q. Can the High-Precision Reducer for Servo Motors AH2 Type (GTR Series) be used in right-angle shaft layouts, and can it replace induction motors in existing equipment?

A. It is a foot-mounted right-angle shaft type that supports right-angle shaft layouts. Because it shares the gear head section with the induction geared motor, it can easily replace existing equipment.

Q. What applications is the High-Precision Reducer for Servo Motors AH2 Type (GTR Series) suited for, such as machine tools and industrial machinery?

A. It is intended for use in machine tools and industrial machinery.

Written by AI based on the content of the source documents.

Source documents

• Catalog SERVO GEARBOXES GUIDE サーボモータ用減速機ガイド Open page 5
  Found on: https://www.nissei-gtr.co.jp/download/catalog/gtr/