Torsion Spring Right-Hand Wound 33-0320

Specifications

How to choose Springs

Points to check when selecting, with the values for this product (33-0320).

1. 1. Select the Spring Rate from the Required Force

   This product: Spring constant k 0.055 N・mm/deg

   The spring rate k is the load required to deflect the spring by 1 mm. Multiply it by the deflection at installation and at operation to confirm that the required force can be obtained. Listed products range widely from 0.007 to 9.91 N/mm, and a margin should be allowed for variation, including the spring rate tolerance (for example, ±10%).

2. 2. Keep Within the Maximum Load and Deflection Limits

   Using the spring beyond its maximum load or maximum deflection causes set (permanent deformation) or breakage. Confirm that the load at the maximum point of the operating stroke is within the maximum load, and for compression springs, that the solid height is not reached.

3. 3. Installation Space, Outside Diameter, and Free Length

   Check that the outside diameter fits the hole or housing, and that the inside diameter does not interfere with the shaft it passes over (applicable shaft diameter). The free length is the length under no load; the difference from the installed length is the initial deflection. Because the coil diameter changes under load, allow sufficient clearance.

4. 4. Select a Material Suited to the Operating Environment

   Piano wire SWP-A has high strength but is prone to rust, and many versions are supplied with rust-preventive oil treatment. For humid environments or environments subject to washing, stainless steel such as SUS304-WPB is a candidate. For strongly corrosive environments such as seawater, titanium is a candidate.

5. 5. Extension Springs: Initial Tension and Hook Shape

   Close-wound extension springs have initial tension, the load required before the spring begins to extend. For applications requiring movement with a small force, check the initial tension value. Also check that the hook shape, such as reverse loop, 90-degree, or 180-degree, matches how the mating part is engaged.

6. 6. Torsion Springs: Angle and Arm Direction

   For torsion springs, check the torque at the operating angle (torsion spring rate × angle) and the arm length. The winding direction should match the direction of twist, and it is common to use the spring in the direction that winds it up. For free-size products, also specify the bending direction.

This guide was written by AI based on the listed products' documents and specification items.

About Springs and all products

Description

Series with inner diameter 3 to 6 mm. Wire diameter 0.3 to 1.0 mm. Available in combinations of 2, 3, and 5 coils and 90°, 135°, and 180° angles.

FAQ

Q. What are the material and winding direction of the Torsion Spring Right-Hand Wound 33-0320?

A. It is a right-hand wound torsion spring made of stainless steel wire. Its key feature is close-wound coils.

Q. What are the dimensions of the 33-0320, such as inner diameter, wire diameter, and arm length?

A. The inner diameter is 3 mm, the wire diameter d is 0.3 mm, and the arm length is 12 mm.

Q. What are the spring constant and operating angle of the 33-0320?

A. The spring constant k is 0.055 N·mm/deg, and the operating angle is 61 deg.

Q. What applications is the 33-0320 suited for?

A. It is used for providing return force to rotating parts.

Q. What combinations are available in the series of the Torsion Spring Right-Hand Wound 33-0320?

A. The series has inner diameters of 3 to 6 mm and wire diameters of 0.3 to 1.0 mm. Available combinations are 2, 3, and 5 coils with 90°, 135°, and 180° angles.

Written by AI based on the content of the source documents.

Source documents

• Catalog スプリングネット 製品カタログ（ばね類） 178 pages Open page 105
  Found on: https://www.samini.co.jp/catalog_list/