Posi-Lock PSL-K(C) Simple Anti-Corrosion Specification

Specifications

ポジロック PSL-K model comparison

Compare 4 models in the same series by specification.

How to choose Shaft coupling

Points to check when selecting, with the values for this product (PSL-K(C)).

1. 1. Allow Margin for Rated Torque

   Select a size whose continuous operating torque is equal to or greater than the load torque transmitted during continuous operation. Check by multiplying the motor's rated torque by a factor corresponding to the frequency of starts and stops and load fluctuations. Listed products have a rated torque of 0.5 to 150 N·m.

2. 2. Verify Peak Torque at Startup Against Maximum Allowable Torque

   This product: Maximum Allowable Torque 750 N・m

   Large instantaneous torques occur during rapid acceleration and deceleration of servo motors, startup, and emergency stops. Confirm that these peak values do not exceed the maximum allowable torque. For taper clamping elements, this value serves as a guide to the torque the clamp can hold.

3. 3. Match Shaft Diameter to Machinable Bore Diameter

   Confirm that the driving and driven shaft diameters fall within the applicable shaft diameter range. When machining pilot-bored products, confirm the bore is within the maximum bore diameter d. If the two shaft diameters differ, check that both hubs have matching bores.

4. 4. Do Not Exceed Maximum Rotational Speed

   Confirm that the maximum operating speed is at or below the coupling's maximum rotational speed. Larger outer diameters are more susceptible to centrifugal force, and the allowable speed tends to be lower. Listed products range from 3600 to 18000 min-1.

5. 5. Check Allowable Mounting Misalignment

   Confirm that the parallel misalignment expected from assembly accuracy is within the maximum allowable eccentricity (0.1 to 0.4 mm for listed products). Compare angular misalignment against the maximum allowable declination (0.5 to 1°). Exceeding these allowances causes early wear of the buffer and increased bearing load.

6. 6. Select Hub Material and Inertia for Responsiveness

   Aluminum alloy hubs are lightweight, low-inertia, and less likely to impair the responsiveness of servo and stepping motors. Cast iron hubs have high inertia and tend to provide stable rotation, and nickel-plated products offer corrosion resistance. In environments requiring rust prevention, also check whether surface treatment is applied.

This guide was written by AI based on the listed products' documents and specification items.

About Shaft coupling and all products

Description

Simple anti-corrosion specification in which the body is treated with electroless Ni plating and the clamping bolts are treated with an anti-corrosion coating.

FAQ

Q. What is the applicable shaft diameter for the Posi-Lock PSL-K(C) Simple Anti-Corrosion Specification in mm?

A. The applicable shaft diameter is φ6 to 42 mm.

Q. How is the anti-corrosion treatment applied to PSL-K(C)?

A. It is a simple anti-corrosion specification in which the body is treated with electroless Ni plating and the clamping bolts are treated with an anti-corrosion coating.

Q. What are the maximum allowable torque and maximum allowable thrust force of PSL-K(C)?

A. The maximum allowable torque is 750 N·m and the maximum allowable thrust force is 36000 N.

Q. What is the ambient operating temperature range of PSL-K(C)?

A. The ambient operating temperature range is -40 to 150 ℃.

Q. Does PSL-K(C) require keyway machining?

A. No, keyway machining is not required.

Written by AI based on the content of the source documents.

Source documents

• Catalog POSI LOCK PSL-G / PSL-D 設計上の確認事項・製品仕様 24 pages Open page 6
  Found on: https://www.mikipulley.co.jp/friction-locking-devices/mechanical/