Bearee™ FL3307 Sliding Sheet for Machine Tools
Model FL3307 / ベアリーFL3307 / NTN Corporation (Official website) / Listed on page 26 of the document
Fluororesin-based sliding sheet for machine tools with improved wear resistance and creep resistance. Features a low dynamic friction coefficient under oil lubrication, and a dedicated adhesive is also available.
Last verified: (date the content was verified against the source document)
A reduced image of the relevant page is quoted from the document. Copyright belongs to NTN Corporation.Request removal
Specifications
| Limit PV (low-speed condition) | 7 MPa・m/min |
|---|---|
| Limit PV (high-speed condition) | 60 MPa・m/min |
| Operating Temperature | 260 ℃ |
Description
Designed for bed sliding surfaces of machine tools, test results indicate lower compressive deformation and longer wear life than competing products. Lighter than steel rolling bearings, and can be used without lubrication.
Features
- Smaller compressive deformation than competing products
- Twice the wear life
- Low friction coefficient
- Usable without lubrication
Applications
- Sliding surfaces of machine tool beds
FAQ
- Q. What applications can Bearee FL3307 be used for?
- A. It is a sliding sheet for sliding surfaces of machine tool beds.
- Q. What are the limiting PV value and operating temperature of FL3307?
- A. The limiting PV value is 7 MPa·m/min under low-speed conditions and 60 MPa·m/min under high-speed conditions. The operating temperature is 260 ℃.
- Q. Can FL3307 be used without lubrication? Also, what are its friction and wear characteristics?
- A. It can be used without lubrication. It has a low dynamic friction coefficient under oil lubrication and is reported to have twice the wear life of competing products.
- Q. How does FL3307 compare with other products in terms of deformation and wear?
- A. Test results show that it has smaller compressive deformation and twice the wear life compared with competing products.
- Q. How does FL3307 differ from steel rolling bearings?
- A. It is lighter than steel rolling bearings.
Written by AI based on the content of the source documents.
Source documents
- Catalog エンジニアリング・プラスチック製しゅう動部品 ベアリー™ 26 pages Open page 26
More products from NTN Corporation
See all →-
Bushings
Bearry™ ARE, AR, and ARF Type Sleeve Bearings
Resin sleeve bearings made with Bearry FL3000. ARE type has bore diameter 3 to 12 mm, AR type has bore diameter 15 to 50 mm, and ARF type is flanged with bore diameter 3 to 50 mm, all standardized. Supports radial load (ARF type also supports axial load).
NTN Corporation
-
Bushings
Bearie™ BRF Series Flanged Sleeve Bearing
Flanged resin bearing injection-molded from Bearie AS5005. Standardized bore diameters of 3 to 25 mm, capable of supporting both radial and axial loads.
NTN Corporation
-
Thrust Washers
Bearee™ TW-Type Thrust Washer
Thrust washer machined from Bearee FL3000 sheet material. Standardized thickness of 0.8 mm and inner diameter of 6 to 50 mm.
NTN Corporation
-
Bushings
Bearry™ MLE Type MLE Bearing
Three-layer high-load bearing made by sintering bronze powder onto a steel backing plate and impregnating the porous layer with Bearry FL7023. Inner diameter 4–60 mm.
NTN Corporation
-
Bushings
Bearye™ ML-Type M Liner Bearing
Thin-walled rolled bushing with FL3060 sheet material bonded to steel plate. Standardized bore diameters from 3 to 70 mm.
NTN Corporation
-
Sliding screw
Bearee™ MSS Miniature Resin Sliding Screw
Low-noise miniature resin sliding screw combining an AS5000 nut with an SUS304 screw shaft. Nominal diameter 4–12 mm.
NTN Corporation