Rod Seal (S09 Single-Acting/Double-Acting Piston Seal, O-Ring Combination PTFE)

Specifications

How to choose Rod Seals

Points to check when selecting, with the values for this product (S09-E / S09-P / S09-D).

1. 1. Match rod diameter and groove dimensions

   This product: Applicable rod diameter d 5 to 1000 mm

   A seal is specified by the combination of applicable rod diameter and installation groove dimensions. The applicable rod diameter of listed products is 5 to 1000 mm. When fitting into an existing groove, check on the drawing that, in addition to the rod diameter, the groove width and groove bottom diameter match the standard combination.

2. 2. Verify cross-section and groove width

   This product: Cross-sectional Dimensions (c/s) 2.45〜13.65 mm

   Cross-section dimension (c/s, radial thickness) corresponds to the groove depth, and groove width L corresponds to the axial length. The listed range is 2.45 to 20 mm cross-section and 2.2 to 50 mm groove width. If dimensions do not match, insufficient squeeze causes leakage, and excessive compression causes early wear.

3. 3. Maximum operating pressure and backup rings

   The maximum operating pressure of listed products is 160 to 700 bar. At high pressure, the seal tends to extrude into the clearance and fail, so consider types with square or trapezoidal backup rings. Confirm that the pressure, including pressure surges (momentary pressure rises), stays within the upper limit.

4. 4. Select material by temperature and fluid compatibility

   PU offers excellent wear resistance, while PTFE has high chemical and heat resistance and low friction. Rubber-based materials vary in oil and heat resistance depending on their compound. Operating temperature ranges differ by material, so select a material that suits the working fluid, such as hydraulic oil, water, or air, and the operating temperature.

5. 5. Check the upper limit of sliding speed

   The maximum sliding speed of listed products is 0.5 to 10 m/s, which varies greatly by material and type. Use at high speed accelerates deterioration due to frictional heat. Check that the maximum cylinder speed is within the upper limit, and consider low-friction PTFE-based types for high-speed applications.

6. 6. Select seal type and operating method

   Rod seals are basically single-acting types that receive pressure from one side. In high-pressure systems, there is a method of combining them with buffer seals. For large machines that are hard to install or have worn rods, chevron packings, which can be selected as split types, are suitable.

This guide was written by AI based on the listed products' documents and specification items.

About Rod Seals and all products

Description

Rod diameter 5 to 1000 mm. S09 is available in materials such as SKF Ecoflon/NBR or FKM, and X-ECOPUR/NBR. Only some profiles are supported for 600 mm and above.

FAQ

Q. What rod diameters can the rod seals S09-E / S09-P / S09-D be used for?

A. The applicable rod diameter d is 5 to 1000 mm. Only some profiles are supported for 600 mm and above.

Q. What are the cross-section dimensions and groove width range of the rod seal S09?

A. The cross-section dimension (c/s) is 2.45 to 13.65 mm, and the groove width L is 2.2 to 9.5 mm.

Q. What applications is the rod seal S09 suited for?

A. It is a single-acting and double-acting piston seal for civil engineering machinery and high-load hydraulic equipment. Its key features are pressure and impact resistance and long service life.

Q. What material types are available for the rod seal S09?

A. It is available in materials such as SKF Ecoflon/NBR or FKM, and X-ECOPUR/NBR. The structure combines an O-ring with PTFE (TPU seal).

Written by AI based on the content of the source documents.

Source documents

• Catalog カスタムエンジニアリングシール シール製品案内 56 pages Open page 47
  Found on: https://azuma-eg.com/catalogue/