Catalog Searcher
Categories

TIH 100m

Model TIH 100m / TIH シリーズ / SKF (Official website) / Listed on page 46 of the document

Medium-sized induction heater for heating bearings. Heats a 97 kg bearing to 110°C in 20 minutes.

Last verified: (date the content was verified against the source document)

TIH 100m on page 46 of SKF "SKFメンテナンス製品と潤滑製品"
Source: SKF「SKFメンテナンス製品と潤滑製品」page 46
A reduced image of the relevant page is quoted from the document. Copyright belongs to SKF.Request removal

Specifications

Maximum Workpiece Mass 120 kg
Applicable bearing bore diameter range 20–400 mm
Heating area (width × height) 155 × 205 mm
Maximum Power Consumption 3,6 kVA
Temperature Control Range 20 – 250 °C
Body Mass 42 kg
External dimensions (width × depth × height) 570 × 230 × 350 mm

TIH シリーズ model comparison

Compare 3 models in the same series by specification.

Model Applicable bearing bore diameter range Maximum Workpiece Mass Heating area (width × height) Maximum Power Consumption Temperature Control Range External dimensions (width × depth × height) Body Mass
TIH 030m 20–300 mm 40 kg 100 × 135 mm 2,0 kVA 20 – 250 °C 460 × 200 × 260 mm 20,9 kg
TIH 100m This product 20–400 mm 120 kg 155 × 205 mm 3,6 kVA 20 – 250 °C 570 × 230 × 350 mm 42 kg
TIH 220m 60–600 mm 300 kg 250 × 255 mm 10,0–11,5 kVA 20 – 250 °C 750 × 290 × 440 mm 86 kg

How to choose Induction heaters

Points to check when selecting, with the values for this product (TIH 100m).

  1. 1. Select capacity suited to workpiece mass

    This product: Maximum Workpiece Mass 120 kg

    The maximum heatable mass varies widely among models, from 40 kg to 1200 kg. Insufficient capacity prolongs heating time and can cause uneven temperature. Select a model with adequate margin over the heaviest bearing or part to be handled, and check the heating performance data in the catalog, such as the mass that can be heated to 110°C within the specified time.

  2. 2. Confirm bore and yoke combination

    This product: Applicable bearing bore diameter range 20–400 mm

    Because the workpiece is heated while threaded over the yoke, the minimum bore that can be handled is determined by the yoke cross-section. Bearings with small bores require thin yokes, so check the number of supplied yokes and the bore range each yoke corresponds to. Dedicated inner ring removal units have a narrow fixed bore range, such as 65 to 130 mm, so match them to the dimensions of the target bearing.

  3. 3. Check that outer diameter and width fit the heating area

    This product: Heating area (width × height) 155 × 205 mm

    If the distance between the support columns or the height is smaller than the workpiece's outer diameter or width, the part cannot be placed. When heating large-diameter or wide bearings, gears or pulleys, also check whether the model has an expanded heating area, or slide-type or swivel-type yokes that make loading and unloading easier.

  4. 4. Verify power capacity and voltage against facility

    This product: Maximum Power Consumption 3,6 kVA

    Maximum power consumption reaches about 20 kVA on large models, and the unit cannot be used if the facility's incoming power capacity or breaker capacity is insufficient. Supported voltages such as 230 V/400 V also differ by model. Confirm the power specification of the installation site in advance and whether the connection cable length reaches.

  5. 5. Check temperature settings and protection functions

    The maximum heating temperature of the listed products is 250°C. Bearings generally lose hardness and precision when overheated, so check for temperature control using a temperature probe, time setting, and overheat protection. When shrink-fitting parts other than bearings, confirm that the temperature can be set to match the required expansion amount.

  6. 6. Body mass and installation and transport methods

    This product: Body Mass 42 kg

    Body mass ranges from 20 kg to over 400 kg. Small models can be carried and used on site, while large models assume floor mounting or movement by forklift or trolley. Also consider workability, including how the workpiece is lifted, the working space, and whether demagnetization and remote control operation are available.

This guide was written by AI based on the listed products' documents and specification items.

About Induction heaters and all products

Description

Suitable for bearings with a bore diameter of 20 to 400 mm, capable of heating up to 120 kg. The large yoke features a swing-arm design.

Features

  • Three yokes supplied as standard
  • Large yoke with swing-arm design
  • Automatic demagnetization function
  • Overheat protection function

Applications

  • Bearing heating
  • Mounting of medium-sized bearings

FAQ

Q. What is the maximum bearing weight that the TIH 100m can heat?
A. It can heat up to 120 kg. It can heat a 97 kg bearing to 110°C in 20 minutes.
Q. What bore diameter bearings is the TIH 100m compatible with?
A. It is compatible with bearings having a bore diameter of 20 to 400 mm.
Q. What are the temperature control range and power consumption of the TIH 100m?
A. The temperature control range is 20 to 250 °C, and the maximum power consumption is 3.6 kVA.
Q. What are the body dimensions and weight of the TIH 100m?
A. The external dimensions (W × D × H) are 570 × 230 × 350 mm, and the body weight is 42 kg.
Q. What are the yokes and safety features of the TIH 100m?
A. Three yokes are supplied as standard, and the large yoke has a swing-arm design. It is equipped with an automatic demagnetization function and an overheat protection function.

Written by AI based on the content of the source documents.

Source documents

More products from SKF

See all →