Catalog Searcher
Categories

TIH L33

Model TIH L33 / TIH L シリーズ / SKF (Official website) / Listed on page 46 of the document

Induction heater for large bearings. Capable of heating bearings up to 700 kg with 15 kVA.

Last verified: (date the content was verified against the source document)

TIH L33 on page 46 of SKF "SKFメンテナンス製品と潤滑製品"
Source: SKF「SKFメンテナンス製品と潤滑製品」page 46
A reduced image of the relevant page is quoted from the document. Copyright belongs to SKF.Request removal

Specifications

Maximum Workpiece Mass 700 kg
Applicable bearing bore diameter range 115–700 mm
Heating area (width × height) 300 × 320 mm
Maximum Power Consumption 15 kVA
Temperature Control Range 0 – 250 °C
Body Mass 140 kg
External dimensions (width × depth × height) 400 × 743 × 550 mm

TIH L シリーズ model comparison

Compare 3 models in the same series by specification.

Model Applicable bearing bore diameter range Maximum Workpiece Mass Heating area (width × height) Maximum Power Consumption Temperature Control Range External dimensions (width × depth × height) Body Mass
TIH L33 This product 115–700 mm 700 kg 300 × 320 mm 15 kVA 0 – 250 °C 400 × 743 × 550 mm 140 kg
TIH L44 150–800 mm 1200 kg 425 × 492 mm 20 kVA 20 – 250 °C 1 200 × 600 × 850 mm 324 kg
TIH L77 150–800 mm 1200 kg 725 × 792 mm 20–24 kVA 20 – 250 °C 1 320 × 600 × 1 150 mm 415 kg

How to choose Induction heaters

Points to check when selecting, with the values for this product (TIH L33).

  1. 1. Select capacity suited to workpiece mass

    This product: Maximum Workpiece Mass 700 kg

    The maximum heatable mass varies widely among models, from 40 kg to 1200 kg. Insufficient capacity prolongs heating time and can cause uneven temperature. Select a model with adequate margin over the heaviest bearing or part to be handled, and check the heating performance data in the catalog, such as the mass that can be heated to 110°C within the specified time.

  2. 2. Confirm bore and yoke combination

    This product: Applicable bearing bore diameter range 115–700 mm

    Because the workpiece is heated while threaded over the yoke, the minimum bore that can be handled is determined by the yoke cross-section. Bearings with small bores require thin yokes, so check the number of supplied yokes and the bore range each yoke corresponds to. Dedicated inner ring removal units have a narrow fixed bore range, such as 65 to 130 mm, so match them to the dimensions of the target bearing.

  3. 3. Check that outer diameter and width fit the heating area

    This product: Heating area (width × height) 300 × 320 mm

    If the distance between the support columns or the height is smaller than the workpiece's outer diameter or width, the part cannot be placed. When heating large-diameter or wide bearings, gears or pulleys, also check whether the model has an expanded heating area, or slide-type or swivel-type yokes that make loading and unloading easier.

  4. 4. Verify power capacity and voltage against facility

    This product: Maximum Power Consumption 15 kVA

    Maximum power consumption reaches about 20 kVA on large models, and the unit cannot be used if the facility's incoming power capacity or breaker capacity is insufficient. Supported voltages such as 230 V/400 V also differ by model. Confirm the power specification of the installation site in advance and whether the connection cable length reaches.

  5. 5. Check temperature settings and protection functions

    The maximum heating temperature of the listed products is 250°C. Bearings generally lose hardness and precision when overheated, so check for temperature control using a temperature probe, time setting, and overheat protection. When shrink-fitting parts other than bearings, confirm that the temperature can be set to match the required expansion amount.

  6. 6. Body mass and installation and transport methods

    This product: Body Mass 140 kg

    Body mass ranges from 20 kg to over 400 kg. Small models can be carried and used on site, while large models assume floor mounting or movement by forklift or trolley. Also consider workability, including how the workpiece is lifted, the working space, and whether demagnetization and remote control operation are available.

This guide was written by AI based on the listed products' documents and specification items.

About Induction heaters and all products

Description

Equipped with a sliding yoke and dual coil design, compatible with bearings having a bore diameter of 115 to 700 mm. Can be transported by forklift.

Features

  • Dual coil design
  • Sliding yoke
  • Compatible with 230V and 400V

Applications

  • Heating large bearings
  • Mounting large bearings

FAQ

Q. What are the applicable bearing bore diameter range and maximum workpiece mass of the TIH L33?
A. The applicable bearing bore diameter range is 115 to 700 mm, and the maximum workpiece mass is 700 kg.
Q. What types of bearings can the TIH L33 be used for heating or mounting?
A. It can be used for heating large bearings and mounting large bearings. It is compatible with bearings having a bore diameter of 115 to 700 mm.
Q. What are the power supply requirements and maximum power consumption of the TIH L33?
A. It is compatible with 230V and 400V, and the maximum power consumption is 15 kVA.
Q. What are the heating area and temperature control range of the TIH L33?
A. The heating area (width × height) is 300 × 320 mm, and the temperature control range is 0 – 250 °C.
Q. What are the body mass, external dimensions, and transportation method of the TIH L33?
A. The body mass is 140 kg, and the external dimensions (width × depth × height) are 400 × 743 × 550 mm. It can be transported by forklift.

Written by AI based on the content of the source documents.

Source documents

More products from SKF

See all →