Catalog Searcher
Categories
🌐 English

Spiraler (Continuous Forming Type, L-Type)

スパイラー / Spring net (Official website)

Large-diameter continuously formed spiraler made from cold-rolled steel sheet. Handles outer diameters of 123 to 314 mm.

Last verified: (date the content was verified against the source document)

Specifications

Material SPCC
Plate thickness t 3.2 mm
Outer diameter D 123〜314 mm
Standard length 1500 mm
Unit price 18000〜25500 円

スパイラー model comparison

Compare 8 models in the same series by specification.

Model Outer diameter D Material Inner diameter Plate thickness t Standard length Unit price
スパイラー（溶接成形品・B型） 90〜425 mm SPHC — 4.5〜6.0 mm 1500〜2000 mm 30800〜95450 円
スパイラー（溶接成形品・U型） 90〜240 mm SUS304 — 3.0 mm 1500 mm 63800〜83050 円
スパイラー（連続成形品・G型ステンレス） 50〜75 mm Stainless steel 20 mm 1.5〜2.0 mm 1500 mm 40000 円
スパイラー（連続成形品・G型鋼板） 97〜250 mm SS400 (6.0t), SPCC (2.3t, 3.2t) — 2.3〜6.0 mm 1500 mm 18500〜35500 円
スパイラー（連続成形品・L型） This product 123〜314 mm SPCC — 3.2 mm 1500 mm 18000〜25500 円
スパイラー（連続成形品・M型） 13〜17 mm SUS304 6.0〜8.0 mm 1.0 mm 1000 mm 3800 円
スパイラー（連続成形品・S型SPCC） 48〜95 mm SPCC — 1.6 mm 1000 mm 4800〜7900 円
スパイラー（連続成形品・S型チタン） 48〜74 mm TP340 (Titanium) — 2 mm 250〜550 mm 16800〜21600 円

How to choose Springs

Points to check when selecting, with the values for this product (Spiraler (Continuous Forming Type, L-Type)).

  1. 1. Select the Spring Rate from the Required Force

    The spring rate k is the load required to deflect the spring by 1 mm. Multiply it by the deflection at installation and at operation to confirm that the required force can be obtained. Listed products range widely from 0.007 to 9.91 N/mm, and a margin should be allowed for variation, including the spring rate tolerance (for example, ±10%).

  2. 2. Keep Within the Maximum Load and Deflection Limits

    Using the spring beyond its maximum load or maximum deflection causes set (permanent deformation) or breakage. Confirm that the load at the maximum point of the operating stroke is within the maximum load, and for compression springs, that the solid height is not reached.

  3. 3. Installation Space, Outside Diameter, and Free Length

    This product: Outer diameter D 123〜314 mm

    Check that the outside diameter fits the hole or housing, and that the inside diameter does not interfere with the shaft it passes over (applicable shaft diameter). The free length is the length under no load; the difference from the installed length is the initial deflection. Because the coil diameter changes under load, allow sufficient clearance.

  4. 4. Select a Material Suited to the Operating Environment

    This product: Material SPCC

    Piano wire SWP-A has high strength but is prone to rust, and many versions are supplied with rust-preventive oil treatment. For humid environments or environments subject to washing, stainless steel such as SUS304-WPB is a candidate. For strongly corrosive environments such as seawater, titanium is a candidate.

  5. 5. Extension Springs: Initial Tension and Hook Shape

    Close-wound extension springs have initial tension, the load required before the spring begins to extend. For applications requiring movement with a small force, check the initial tension value. Also check that the hook shape, such as reverse loop, 90-degree, or 180-degree, matches how the mating part is engaged.

  6. 6. Torsion Springs: Angle and Arm Direction

    For torsion springs, check the torque at the operating angle (torsion spring rate × angle) and the arm length. The winding direction should match the direction of twist, and it is common to use the spring in the direction that winds it up. For free-size products, also specify the bending direction.

This guide was written by AI based on the listed products' documents and specification items.

About Springs and all products

Description

Seamless construction with a smooth surface and good friction resistance. Maximum length is 1500 to 2000 mm depending on model.

Features

  • Large diameter
  • Seamless continuous forming

Applications

  • Conveying

FAQ

Q. What is the range of outer diameter and maximum length for the Spiraler (Continuous Forming Type, L-Type)?
A. It handles outer diameters of 123 to 314 mm. Maximum length is 1500 to 2000 mm depending on model.
Q. What are the material and sheet thickness of the Spiraler (Continuous Forming Type, L-Type)?
A. The material is SPCC (cold-rolled steel sheet), and the sheet thickness t is 3.2 mm.
Q. Is the Spiraler (Continuous Forming Type, L-Type) a seamless structure? What are its surface characteristics?
A. It is seamless, with a smooth surface and good friction resistance.
Q. What are the applications and standard length of the Spiraler (Continuous Forming Type, L-Type)?
A. It is used for conveying applications. The standard length is 1500 mm.

Written by AI based on the content of the source documents.

Source documents

Similar products (other manufacturers)

Springs products, ordered by similarity of specifications and applications.

More products from Spring net

See all →