Extension Spring with Plates 28-054 (Stainless Steel)

Specifications

How to choose Springs

Points to check when selecting, with the values for this product (28-054).

1. 1. Select the Spring Rate from the Required Force

   This product: Spring constant k 0.16 N/mm

   The spring rate k is the load required to deflect the spring by 1 mm. Multiply it by the deflection at installation and at operation to confirm that the required force can be obtained. Listed products range widely from 0.007 to 9.91 N/mm, and a margin should be allowed for variation, including the spring rate tolerance (for example, ±10%).

2. 2. Keep Within the Maximum Load and Deflection Limits

   This product: Maximum load 9.37 N

   Using the spring beyond its maximum load or maximum deflection causes set (permanent deformation) or breakage. Confirm that the load at the maximum point of the operating stroke is within the maximum load, and for compression springs, that the solid height is not reached.

3. 3. Installation Space, Outside Diameter, and Free Length

   This product: Outer diameter D 5 mm

   Check that the outside diameter fits the hole or housing, and that the inside diameter does not interfere with the shaft it passes over (applicable shaft diameter). The free length is the length under no load; the difference from the installed length is the initial deflection. Because the coil diameter changes under load, allow sufficient clearance.

4. 4. Select a Material Suited to the Operating Environment

   Piano wire SWP-A has high strength but is prone to rust, and many versions are supplied with rust-preventive oil treatment. For humid environments or environments subject to washing, stainless steel such as SUS304-WPB is a candidate. For strongly corrosive environments such as seawater, titanium is a candidate.

5. 5. Extension Springs: Initial Tension and Hook Shape

   Close-wound extension springs have initial tension, the load required before the spring begins to extend. For applications requiring movement with a small force, check the initial tension value. Also check that the hook shape, such as reverse loop, 90-degree, or 180-degree, matches how the mating part is engaged.

6. 6. Torsion Springs: Angle and Arm Direction

   For torsion springs, check the torque at the operating angle (torsion spring rate × angle) and the arm length. The winding direction should match the direction of twist, and it is common to use the spring in the direction that winds it up. For free-size products, also specify the bending direction.

This guide was written by AI based on the listed products' documents and specification items.

About Springs and all products

Description

Wire diameter 0.6 mm, outer diameter 5 mm, spring constant 0.16 N/mm at F dimension 50 mm. Available in a series with outer diameters of 5 to 18 mm.

FAQ

Q. What is the material of Extension Spring with Plates 28-054 (Stainless Steel), and how is the F dimension specified?

A. It is made of SUS304-WPB. It is an extension spring with plates attached at both ends, and it is manufactured to the specified F dimension.

Q. What are the wire diameter, outer diameter, and spring constant of 28-054?

A. The wire diameter d is 0.6 mm and the outer diameter D is 5 mm. The spring constant at an F dimension of 50 mm is 0.16 N/mm.

Q. What are the maximum deflection (maximum extension) and maximum load of 28-054?

A. The maximum deflection (maximum extension) is 51 mm and the maximum load is 9.37 N.

Q. What applications is 28-054 suitable for?

A. It is used for tensile support of equipment and for return applications.

Q. Are there products of Extension Spring with Plates 28-054 with different outer diameters?

A. There is a series with outer diameters of 5 to 18 mm.

Written by AI based on the content of the source documents.

Source documents

• Catalog スプリングネット 製品カタログ（ばね類） 178 pages Open page 94
  Found on: https://www.samini.co.jp/catalog_list/