Ultra Super Chain RF140-US-N-1
Model RF140-US-N-1 / ウルトラスーパチェーン US-N仕様 / Tsubakimoto Chain Co. (Official website)
Successor to the US-spec roller chain. US-spec sales were discontinued at the end of September 2016; the product is currently quote-based.
Last verified: (date the content was verified against the source document)
Specifications
| Pin diameter D | 12.71 mm |
|---|
ウルトラスーパチェーン US-N仕様 model comparison
Compare 6 models in the same series by specification.
| Model | Pin diameter D |
|---|---|
| RF100-US-N-1 | 9.54 mm |
| RF120-US-N-1 | 11.11 mm |
| RF140-US-N-1 This product | 12.71 mm |
| RF160-US-N-1 | 14.29 mm |
| RF200-US-N-1 | 19.85 mm |
| RF240-US-N-1 | 23.81 mm |
How to choose Chain
Points to check when selecting, with the values for this product (RF140-US-N-1).
-
1. Select a pitch that matches the sprocket
The pitch must match the tooth profile of the sprocket, and different pitches cannot be combined. Listed products range from 31.75 to 76.2 mm. Larger pitches increase power transmission capacity, but they also add mass and cause greater vibration and noise at high rotational speeds, so the choice should be based on both rotational speed and load.
-
2. Check the load against the maximum allowable tension
This is the upper limit of tension that may be applied in actual use. Multiply the chain tension calculated from transmitted power and speed by a service factor that accounts for starting shock and load fluctuation, and confirm that the result is at or below this value. Listed products range from 39.2 to 151 kN, and heavy-duty types have higher values even at the same pitch.
-
3. The minimum tensile strength is the guaranteed breaking value
The minimum tensile strength is the guaranteed breaking load, and listed products range from 149 to 853 kN. The average tensile strength is a higher mean value than this, so the minimum value is used for strength calculations. It is not used as the basis for working load, but is used to check the safety margin against overload.
-
4. Verify the inner link width against the tooth width
The inner link width corresponds to the tooth width of the sprocket. Some heavy-duty types can use sprockets for standard roller chains, but there are cases where cast iron sprockets are not permitted, so the tooth width and material conditions must be checked together.
-
5. Check compatibility by roller diameter and pin diameter
The roller diameter relates to the tooth bottom shape, and the pin diameter relates to connecting links and wear life. In some cases, successor specifications cannot be connected to previous specifications, so when partially replacing or adding links to an existing chain, dimensions and connectability should be verified against the manufacturer's documentation.
-
6. Confirm link count and lead time conditions
Types without offset links (half links) can only be used with an even number of links, and allowance for adjusting the center distance is required. Also, some large-size products are made to order or quoted on each request, so spare parts procurement timing should be included in planning.
This guide was written by AI based on the listed products' documents and specification items.
Description
Materials have been reviewed, and the minimum breaking strength and maximum allowable load are equal to or higher than those of the US-spec chain. The pin diameter is smaller than before, so it cannot be connected to the former US-spec chain. Sprockets currently in use can continue to be used as they are.
Features
- Successor to US-spec product
- Quote-based product
- Cannot be connected to former US-spec chain
FAQ
- Q. Can RF140-US-N-1 be connected to former US-spec chains?
- A. No, it cannot be connected to former US-spec chains because its pin diameter is smaller than before.
- Q. Can sprockets currently in use be used with RF140-US-N-1 as they are?
- A. Yes, sprockets currently in use can continue to be used as they are.
- Q. How do the minimum breaking strength and maximum allowable load of RF140-US-N-1 compare with the US-spec chain?
- A. Materials have been reviewed, and the minimum breaking strength and maximum allowable load are equal to or higher than those of the US-spec chain.
- Q. What is the pin diameter of Ultra Super Chain RF140-US-N-1?
- A. The pin diameter D is 12.71 mm.
Written by AI based on the content of the source documents.
Source documents
- Document ウルトラスーパチェーン US 仕様の発売中止と US-N 仕様について 1 pages
Similar products (other manufacturers)
Chain products, ordered by similarity of specifications and applications.
-
Drive shaft
Drive Shaft for Rolling Mills (Block Type)
A high-strength, long-life drive shaft that drives rolls in rolling mills. Used under demanding conditions such as plate rolling mills and hot rolling mills.
JTEKT Corporation
-
Torque limiter
Hyper Coupling (Torque Limiter)
A torque limiter that protects rolling mill drive systems from excessive torque. Improves operating accuracy and durability, and shortens recovery time.
JTEKT Corporation
-
Shaft coupling
SERVORIGID SRG
Ultra-high rigidity rigid coupling for servo motors. Its structure does not absorb shaft misalignment, achieving high torsional rigidity and low inertia.
Miki Pulley
-
Shaft coupling
Posi-Lock PSL-K Standard Type
Model: PSL-K
Flanged standard type that clamps shaft and hub through the wedge action of tapered surfaces. Accommodates shaft diameters of φ6 to 42 mm.
Miki Pulley
More products from Tsubakimoto Chain Co.
See all →-
Chain
Ultra Super Chain RF100-US-1
Model: RF100-US-1
Heavy-duty drive chain with 31.75 mm pitch. Minimum tensile strength 149 kN, maximum allowable tension 39.2 kN.
Tsubakimoto Chain Co.
-
Chain
Ultra Super Chain RF120-US-1
Model: RF120-US-1
High-strength drive chain with 38.10 mm pitch. Minimum tensile strength 213 kN, maximum allowable tension 53.9 kN.
Tsubakimoto Chain Co.
-
Chain
Ultra Super Chain RF140-US-1
Model: RF140-US-1
Heavy-duty drive chain with 44.45 mm pitch. Minimum tensile strength 273 kN, maximum allowable tension 63.7 kN.
Tsubakimoto Chain Co.
-
Chain
Ultra Super Chain RF160-US-1
Model: RF160-US-1
Heavy-duty drive chain with 50.80 mm pitch. Minimum tensile strength 341 kN, maximum allowable tension 85.3 kN.
Tsubakimoto Chain Co.
-
Chain
Ultra Super Chain RF200-US-1
Model: RF200-US-1
Heavy-duty drive chain with 63.50 mm pitch. Minimum tensile strength 580 kN, maximum allowable tension 108 kN.
Tsubakimoto Chain Co.
-
Chain
Ultra Super Chain RF240-US-1
Model: RF240-US-1
Heavy-duty drive chain with 76.20 mm pitch. Minimum tensile strength 853 kN, maximum allowable tension 151 kN.
Tsubakimoto Chain Co.