Catalog Searcher
Categories
🌐 English

Spaflex Coupling CL-150

Model CL-150 / スパフレックス CLモデル / Miki Pulley (Official website) / Listed on page 2 of the document

Large shaft coupling with cast iron hub and nickel-plated finish. Continuous torque 100 N·m.

Last verified: (date the content was verified against the source document)

Spaflex Coupling CL-150 on page 2 of Miki Pulley "スパフレックス カップリング"
Source: Miki Pulley「スパフレックス カップリング」page 2
A reduced image of the relevant page is quoted from the document. Copyright belongs to Miki Pulley.Request removal

Specifications

Continuous torque 100 N·m
Maximum Allowable Torque 300 N·m
Maximum permissible eccentricity 0.4 mm
Maximum permissible angular misalignment 1.0 °
Maximum permissible axial displacement ±1.0 mm
Maximum Rotational Speed 3600 min-1
Moment of inertia 6.58×10-3 kg·m²
Mass 5.15 kg
Price 6770 円
Pilot hole diameter d 15.0 mm
Maximum hole diameter d 46 mm
Outer diameter D 96 mm
Overall length L 118.5 mm

スパフレックス CLモデル model comparison

Compare 5 models in the same series by specification.

Model Continuous torque Maximum Allowable Torque Maximum hole diameter d Outer diameter D Maximum Rotational Speed Pilot hole diameter d Overall length L Maximum permissible eccentricity
CL-095 10 N·m 30 N·m 29 mm 55 mm 6000 min-1 11.0 mm 69.0 mm 0.3 mm
CL-100 25 N·m 75 N·m 37 mm 66 mm 5000 min-1 11.0 mm 88.0 mm 0.3 mm
CL-110 50 N·m 150 N·m 48 mm 85 mm 4000 min-1 11.0 mm 110.0 mm 0.3 mm
CL-150 This product 100 N·m 300 N·m 46 mm 96 mm 3600 min-1 15.0 mm 118.5 mm 0.4 mm
CL-190 150 N·m 450 N·m 58 mm 115 mm 3600 min-1 15.0 mm 138.5 mm 0.4 mm

How to choose Shaft coupling

Points to check when selecting, with the values for this product (CL-150).

  1. 1. Allow Margin for Rated Torque

    This product: Continuous torque 100 N·m

    Select a size whose continuous operating torque is equal to or greater than the load torque transmitted during continuous operation. Check by multiplying the motor's rated torque by a factor corresponding to the frequency of starts and stops and load fluctuations. Listed products have a rated torque of 0.5 to 150 N·m.

  2. 2. Verify Peak Torque at Startup Against Maximum Allowable Torque

    This product: Maximum Allowable Torque 300 N·m

    Large instantaneous torques occur during rapid acceleration and deceleration of servo motors, startup, and emergency stops. Confirm that these peak values do not exceed the maximum allowable torque. For taper clamping elements, this value serves as a guide to the torque the clamp can hold.

  3. 3. Match Shaft Diameter to Machinable Bore Diameter

    This product: Maximum hole diameter d 46 mm

    Confirm that the driving and driven shaft diameters fall within the applicable shaft diameter range. When machining pilot-bored products, confirm the bore is within the maximum bore diameter d. If the two shaft diameters differ, check that both hubs have matching bores.

  4. 4. Do Not Exceed Maximum Rotational Speed

    This product: Maximum Rotational Speed 3600 min-1

    Confirm that the maximum operating speed is at or below the coupling's maximum rotational speed. Larger outer diameters are more susceptible to centrifugal force, and the allowable speed tends to be lower. Listed products range from 3600 to 18000 min-1.

  5. 5. Check Allowable Mounting Misalignment

    This product: Maximum permissible eccentricity 0.4 mm

    Confirm that the parallel misalignment expected from assembly accuracy is within the maximum allowable eccentricity (0.1 to 0.4 mm for listed products). Compare angular misalignment against the maximum allowable declination (0.5 to 1°). Exceeding these allowances causes early wear of the buffer and increased bearing load.

  6. 6. Select Hub Material and Inertia for Responsiveness

    This product: Moment of inertia 6.58×10-3 kg·m²

    Aluminum alloy hubs are lightweight, low-inertia, and less likely to impair the responsiveness of servo and stepping motors. Cast iron hubs have high inertia and tend to provide stable rotation, and nickel-plated products offer corrosion resistance. In environments requiring rust prevention, also check whether surface treatment is applied.

This guide was written by AI based on the listed products' documents and specification items.

About Shaft coupling and all products

Description

Large shaft coupling consisting of a cast iron hub and an NBR spider. The hub is nickel-plated for rust prevention.

Features

  • High inertia with cast iron hub
  • Rust prevention by nickel plating
  • Connection and disconnection possible by axial movement only

Applications

  • General-purpose motors
  • Stepping motors
  • Servo motors
  • Detectors
  • Engines

FAQ

Q. What are the applications and usable conditions for CL-150?
A. Applications are general-purpose motors, stepping motors, servo motors, detectors, and engines. Continuous torque is 100 N·m, maximum allowable torque is 300 N·m, and maximum rotational speed is 3600 min-1.
Q. What are the allowable shaft misalignment values for CL-150: parallel offset, angular misalignment, and axial displacement?
A. Maximum allowable parallel offset is 0.4 mm, maximum allowable angular misalignment is 1.0 °, and maximum allowable axial displacement is ±1.0 mm.
Q. What are the materials and rust prevention treatment of CL-150?
A. The hub is made of cast iron and is nickel-plated for rust prevention. The spider is made of NBR.
Q. How does CL-150 connect and disconnect shafts?
A. It can be connected and disconnected by axial movement only.
Q. What are the bore diameters and external dimensions of CL-150?
A. Pilot bore diameter d is 15.0 mm, maximum bore diameter d is 46 mm, outer diameter D is 96 mm, and overall length L is 118.5 mm.

Written by AI based on the content of the source documents.

Source documents

Similar products (other manufacturers)

Shaft coupling products, ordered by similarity of specifications and applications.

More products from Miki Pulley

See all →