Catalog Searcher
Categories
🌐 English

Set Collar SCK1215C

Model SCK1215C / SCK / Iwata Seisakusho Co., Ltd. (Official website) / Listed on page 1 of the document

Wedge-clamp type set collar with bore diameter φ12. Normal type has allowable thrust load of 4800N and allowable radial load of 30.2 N·m when tightened.

Last verified: (date the content was verified against the source document)

Set Collar SCK1215C on page 1 of Iwata Seisakusho Co., Ltd. "セットカラー 技術資料 125 クサビカラー性能評価試験結果表"
Source: Iwata Seisakusho Co., Ltd.「セットカラー 技術資料 125 クサビカラー性能評価試験結果表」page 1
A reduced image of the relevant page is quoted from the document. Copyright belongs to Iwata Seisakusho Co., Ltd..Request removal

Specifications

Inner diameter d 12 mm
Allowable thrust load 4800 N
Permissible radial load 30.2 N·m
Allowable thrust load (clamp lever) 1700 N
Allowable radial load (clamp lever) 9.7 N·m

SCK model comparison

Compare 20 models in the same series by specification.

Model Inner diameter d Allowable thrust load Allowable thrust load (clamp lever) Permissible radial load Allowable radial load (clamp lever)
SCK1015C 10 mm 5100 N 1900 N 25.2 N·m 9.7 N·m
SCK1015S 10 mm 2500 N 900 N 15.2 N·m 6.2 N·m
SCK1215C This product 12 mm 4800 N 1700 N 30.2 N·m 9.7 N·m
SCK1215S 12 mm 2900 N 800 N 19.1 N·m 7.2 N·m
SCK1515C 15 mm 4400 N 1900 N 37.5 N·m 10.8 N·m
SCK1515S 15 mm 2500 N 780 N 22.7 N·m 9.1 N·m
SCK1615C 16 mm 4300 N 1800 N 33.1 N·m 13.1 N·m
SCK1615S 16 mm 2400 N 950 N 26.8 N·m 10.0 N·m
SCK2015C 20 mm 7000 N 2300 N 60.6 N·m 16.2 N·m
SCK2015S 20 mm 2900 N 1100 N 30.0 N·m 11.0 N·m
SCK2515C 25 mm 5100 N 2000 N 60.2 N·m 15.4 N·m
SCK2515S 25 mm 2600 N 1020 N 39.1 N·m 14.3 N·m
SCK3015C 30 mm 5400 N 1800 N 97.2 N·m 22.3 N·m
SCK3015S 30 mm 2300 N 870 N 44.8 N·m 21.2 N·m
SCK3520C 35 mm 5200 N 1370 N 97.3 N·m 26.7 N·m
SCK3520S 35 mm 4400 N 1200 N 96.3 N·m 27.8 N·m
SCK4020C 40 mm 5200 N 1780 N 135.1 N·m 27.1 N·m
SCK4020S 40 mm 4000 N 1300 N 143.2 N·m 40.9 N·m
SCK5020C 50 mm 5500 N 1320 N 135.1 N·m 35.0 N·m
SCK5020S 50 mm 3400 N 1100 N 142.3 N·m 44.7 N·m

How to choose Set collar

Points to check when selecting, with the values for this product (SCK1215C).

  1. 1. Select a bore matching the shaft diameter

    This product: Inner diameter d 12 mm

    Select the bore d to match the applicable shaft diameter. Listed products cover a range of φ5 to 110. Because the combination of shaft tolerance and collar bore tolerance affects clamping force and ease of fitting, check the bore tolerance as well as the shaft diameter.

  2. 2. Confirm the required axial holding force

    This product: Allowable thrust load 4800 N

    The allowable thrust load is the axial load that can be held without slipping axially, and listed products range from 2300 to 149040 N. Even with the same bore, values differ by type; for example, at φ30 there are products rated at 5400 N and 2300 N. Select a model with sufficient margin over the axial load applied.

  3. 3. Also check rotational holding force

    This product: Permissible radial load 30.2 N·m

    The allowable radial load is the torque that can be held without slipping in the rotational direction, and listed products range from 3.6 to 449.5 N·m. In applications where torque or rotational force acts on the collar, confirm that this value exceeds the operating conditions.

  4. 4. Choose the clamping method based on how often it is adjusted

    For positions that change frequently, the lever type is convenient because no tools are required, but its holding force is lower than with bolt tightening. The listed lever-tightened thrust load is 780 to 2300 N. If the shaft must not be damaged, select the clamp or wedge type.

  5. 5. Tighten to the recommended torque

    The holding forces in the catalog are values obtained when tightened to the recommended tightening torque. Listed products range from 0.9 to 267.2 N·m, and the value varies greatly with bolt size. Using a torque wrench to observe the specified value helps prevent loosening and damage to the body.

  6. 6. Select material and surface treatment suited to the environment

    S45C offers high strength and is protected against rust by black oxide or electroless nickel plating. For humid environments or areas with washdown, SUS304 is chosen, and for weight reduction, aluminum alloys such as A2017 are selected. However, holding force varies with material, so check it together with the load values.

This guide was written by AI based on the listed products' documents and specification items.

About Set collar and all products

Features

  • Two types: normal (hex socket head bolt) and clamp lever

FAQ

Q. What are the bore diameter and allowable thrust load of SCK1215C?
A. The bore diameter d is 12 mm. The allowable thrust load of the normal type is 4800 N.
Q. How do the allowable loads differ between the normal type and clamp lever type of SCK1215C?
A. The normal type has an allowable thrust load of 4800 N and an allowable radial load of 30.2 N·m. The clamp lever type has an allowable thrust load of 1700 N and an allowable radial load of 9.7 N·m.
Q. What types are available for SCK1215C?
A. There are two types: normal (hex socket head bolt) and clamp lever.
Q. What is the structure of SCK1215C set collar?
A. It is a wedge-clamp type set collar with bore diameter φ12.

Written by AI based on the content of the source documents.

Source documents

Similar products (other manufacturers)

Set collar products, ordered by similarity of specifications and applications.

More products from Iwata Seisakusho Co., Ltd.

See all →