Catalog Searcher
Categories

Heavy-Duty Rear Puller TMBS 150E

Model TMBS 150E / TMBS E / SKF (Official website) / Listed on page 30 of the document

Rear puller kit for large-diameter shafts. Equipped with a hydraulic spindle with a maximum force of 100 kN and extension rods.

Last verified: (date the content was verified against the source document)

Heavy-Duty Rear Puller TMBS 150E on page 30 of SKF "SKFメンテナンス製品と潤滑製品"
Source: SKF「SKFメンテナンス製品と潤滑製品」page 30
A reduced image of the relevant page is quoted from the document. Copyright belongs to SKF.Request removal

Specifications

Maximum Stroke 80 mm
Maximum Pull-out Force 100 kN
Maximum distance from shaft end 120–816 mm
Applicable shaft diameter 35–150 mm
Hydraulic Cylinder Threaded Portion 1 1/2"-16 UN
Mass 17 kg

TMBS E model comparison

Compare 3 models in the same series by specification.

Model Maximum Pull-out Force Applicable shaft diameter Maximum Stroke Maximum distance from shaft end Hydraulic Cylinder Threaded Portion Mass
TMBS 100E 100 kN 20–100 mm 80 mm 120–816 mm 1 1/2"-16 UN 13.5 kg
TMBS 150E This product 100 kN 35–150 mm 80 mm 120–816 mm 1 1/2"-16 UN 17 kg
TMBS 50E 30 kN 7–50 mm — 110 mm — 1.8 kg

How to choose Puller

Points to check when selecting, with the values for this product (TMBS 150E).

  1. 1. Allow margin in the required pulling force

    This product: Maximum Pull-out Force 100 kN

    Larger interference fits and larger parts require more force. The listed maximum pulling forces range from 6 to 500 kN, and hydraulic types are mainly used at around 100 kN and above. Also check whether a safety valve is provided to prevent overloading.

  2. 2. Confirm the outer diameter falls within the grip width

    The outer diameter of the bearing or part to be removed must fall within the outer diameter range the claws can grip. Claw engagement tends to be shallow at the ends of the range, so select a model with some margin. When used as an internal puller, check the inner-diameter grip width.

  3. 3. Confirm the claws reach the back of the part

    If the effective arm length is insufficient for the part thickness or its position from the shaft end, the claws will not engage the back face. For bearings far from the shaft end, models supplied with extension rods or extension pieces, or models with a large maximum reach from the shaft end, are suitable.

  4. 4. Match the bearing bore and shaft diameter

    Back-face pullers and inner race pullers have defined applicable ranges for bearing bore and shaft diameter. Listed products cover bearing bores from 7 to 160 mm. Check the bore, outer diameter and width of the target bearing from its model number against the applicable range.

  5. 5. Check the pulling travel and stroke

    This product: Maximum Stroke 80 mm

    Fully removing a bearing from the shaft requires travel equal to the fitted length. If the maximum stroke is insufficient, extension pieces must be added partway through the work, so select a model by comparing its stroke with the fitted length.

  6. 6. Select the type to suit the mounting condition

    Inner race or forcing-type pullers suit cases where the outer ring is press-fitted into a housing. Back-face or collet-type pullers suit cases where there is little clearance behind the inner race. Jaw pullers suit cases where the outer circumference can be gripped. The suitable type therefore depends on the mounting condition.

This guide was written by AI based on the listed products' documents and specification items.

About Puller and all products

Description

Model with a larger applicable shaft diameter, using the same hydraulic spindle configuration as the TMBS 100E.

Features

  • Equipped with hydraulic spindle
  • Safety valve included
  • Extension rod included

Applications

  • Bearing removal from large-diameter shafts
  • Bearing removal at positions away from the shaft end

FAQ

Q. What size of shaft can the TMBS 150E be used on?
A. The applicable shaft diameter is 35–150 mm. The maximum distance from the shaft end is 120–816 mm.
Q. What are the maximum pulling force and maximum stroke of the TMBS 150E?
A. The maximum pulling force is 100 kN and the maximum stroke is 80 mm. It is equipped with a hydraulic spindle.
Q. What applications is the TMBS 150E suited for?
A. It is used for bearing removal from large-diameter shafts and for bearing removal at positions away from the shaft end. Extension rods are included.
Q. What are the safety features and body weight of the TMBS 150E?
A. It is equipped with a safety valve. The mass is 17 kg.

Written by AI based on the content of the source documents.

Source documents

More products from SKF

See all →